THSC SERIES

Waterworks, irrigation and drainage pumping stations. Power stations, industrial water supply systems, fire fighting applications in refineries

OPERATING DATA

Pump sizes DN 80 up to 900mm
Capacities Q up to 5000I/s
Total heads H up to 200m
Operating pressure P up to 30bar
Operating temperature I up to +105°C

MODEL CODE

Series : THSC
Suction (mm) : 200
Discharge (mm) : 125
Nominal Impeller diameter (mm) : 290
Vertical type : v
Category:

Reviews

There are no reviews yet.

Be the first to review “THSC SERIES”

Your email address will not be published. Required fields are marked *

Related products

  • DUCKBILL SERIES

    Trosx duckbill check valve and perfectly design for flood control & protect discharge line back flow, especially from rising of water level & also to ensure storm water does not back flow back to catchment area

    1.PUMPED LIQUIDS

    Thin, non-explosive liquids, not containing solid particles. The liquid must not attack the pump materials chemically. When pumping liquids with a density or viscosity higher than that of water, motor with correspondingly higher outputs must be used, if required.

    ADVANTAGE OF DESIGN:

    q. 100% elastomer construction b. No moving parts c. Minimum maintenance cost d. Low cracking pressure e. Low pressure loss f. No rust or corrode g. Will not warp or freeze open or shut down h. Self-draining & eliminate standing water i. Prevent back flow j. Non slam design, silent operation

    WORKING PRINCIPLE:

    Whenever the valve inlet exceeded back pressure at the outlet valve, the flow mechanism will be created, as show above.

    When the backpressure exceeded the line pressure, the duckbill will be closed automatically and prevent back flow.

    APPLICATION & INSTALLATION:

    a. Sewer application b. Flood control c. Pumping line d. Mining tailing systems e. Dredging f. Scrubber systems g. We/dry wall

    MATERIAL OF CONSTRUCTIONS & APPLICATION:

    •  EPDM – water, weak acid, ozone and some hydrocarbon
    • NBR (Buna-N) – Oily water & waste water, fats, moderate chemical & grease waste water
    • Natural Rubber (NR) – Alcohols, organics acid, ketones, moderate acid & abrasive waste water
    • Hypalon (CSM) – Strong acids, ozone, oxidizing chemicals
    • Neoprene (CR) – Oily water, grease and fats
    • Viton (FKM) – Aromatic, solvents, halogenated, hydrocarbon, acid & oils
    Read more

  • TFG SERIES

    The TFG series are with two back to back impellers (with axial thrust balancing). It uses is ideal for high head values where single impeller types are hard to reach. Suitable for civil and industrial boosting, firefighting plant, flood irrigations, etc. it uses to pump clean water and chemically non-aggressive liquid. Particularly be used for increasing the supply pressure, feeding boilers and loading extremely. These pumps should be installed in a covered area, protected against the weather.

    GENERAL

    Pump body : Cast iron
    Impeller : Brass
    Motor : Closed, Externally ventilated
    Insulation class : F
    Protection class : IP54
    Duty : Continuously rated
    Mechanical seal Ø16, Ø18, Ø25 Ceramic steatite / Graphite
    Shaft Stainless steel AISI 420
    Read more

  • TVI (BGI) SERIES

    Close-coupled, single-impeller, centrifugal pumps electric motor with directly connected to the pump.Pump casing with suction and delivery connections with the same diameter and on the same axis (in-line)

    APPLICATIONS

    • For clean liquids, without abrasives, which are non-aggressive for the pump materials (contents of solid up to 0.2 %)
    • For heating, conditioning, cooling and circulation plants
    • For civil and industrial applications

    OPERATING CONDITIONS

    • Liquid temperature up to 90°C • Ambient temperature up to 40° • Total suction lift up to 7 meter • Maximum permissible working pressure up to 10 bar • Continuous duty • Three phase 415 V/50 Hz induction Motor • Insulation class F • Protection IP54
    Read more